Sword Models Curtis P40 Kittyhawk III - Part III

Alright... once again, it was time for some fun with the airbrush. First step - couple of thin layers of Vallejo's grey primer straight out of the can. Next, preshading stage, where all panel lines are outlined with thinned down black paint. Once these steps were completed, proper paint job could begin.

In case of the Kittyhawk, I had a bit of a problem with paint selection. Sword Miniatures doesn't provide references to specific paint manufacturers, only generic paint names such as Azure Blue or Mid Stone. Luckily, when it comes to Allied airplanes in North Africa, it's pretty easy to figure out what colors are historically correct. After a short online research session, all that remained was the decision front is what brand of colors to use. Based on ease of availability and previous experience, I choose to go yet again with Lifecolor acrylics - UA098 Azure Blue for the underside and UA097 Middle Stone / UA092 Dark Earth for camouflage scheme of upper surfaces.

For the sake of personal challenge, I decided to paint the cammo scheme without any masks. Not sure if it's historically correct, but I wanted to paint a soft-edged cammo pattern for the longest of times and this opportunity was to good to be allowed to pass by. Also, this way I would get the opportunity to train my handling of the airbrush. Also, I wanted for this model to have a camouflage with feathered edges. To get better control of spraying pattern, I switched to 0.3 mm needle in my Badger 150. A short training session on a piece of paper revealed noticeable difference in handling - on positive side, the spray pattern was (as expected) much thinner. On the negative side, the airbrush showed much higher tendency for clogging. Thinning the paint a bit more normally did alleviate this problem a bit. Increasing the air pressure did not - the only result of that action was much higher tendency for unintentional spatter and spidering patterns.

Once I've gotten a bit of a grasp of new characteristics of my airbrush, painting freehand actually turned out to be a rather enjoyable experience. I'm happy to say that I managed to get most of camouflage right on  first try. Places where I messed up were easily corrected with a second pass with the airbrush. I also discovered that minor spatter spots can be corrected with a normal brush, without noticeable blemishes on the finish.

Middle Stone cammo pattern applied. Once again, I managed to pretty much eradicate the shade effect I tried to create with black lines outlining the panel edges.

How to make life difficult for oneself - initially I decided not to mount the drop tank on this model.
I then changed my mind... but not before being done with all the painting of the airplane body. Once the drop tank was in place, it had to be painted and I was pretty sure that this would result in unintentional oversprays  on already painted areas. In the end, common kitchen plastic foil turned out to be perfect as masking material for already painted areas.

Sword Models Curtis P40 Kittyhawk III - Part II

Well, I'm starting to believe that "limited run" is hobby's shorthand for "Just so you know, this puppy will fight you every step of the way and be general pain in the arse". At least that's what I was pretty convinced of as I've got through the dreaded step of putting the cockpit together and closing the fuselage.

Why dreaded, you ask? Well, I don't know how other model builders think about this step, but for me this stage is always a bit unnerving - not only is everything (ideally) supposed to fit perfectly together (which it never does), but correction of any mistakes or misalignments can be a bit of a problem. Thus, this is always this stage of building process that requires for me take a deeeep breath before I get on with it.

In this particular case, as soon as I was dry-fitting the instrument panel, I knew there would be problems. I don't know how the designer imagined for it to work, but in my opinion there wasn't enough surface to glue together. There is about one square millimeter on each side of the panel and on the sides of the cockpit to work with. I know, super-glue is the obvious answer. But only the normal plastic glue was an option here, as I felt I needed time to adjust position of the panel, if I didn't get it right from the start. That in itself provided a problem of its own - as everyone knows, plastic glue actually melts plastic... which, in this case were the minuscule sections I tried to fuse together.

Needless to say, things went rather badly on first try and every attempt to get the panel into place only made the situation even worse. In the end, I 'spot-welded' the part to the cockpit in a rather crooked position. Only couple of days later I came to think of proper solution for the problem - all I had to do was to glue small extensions out of scrap plastic to the sides of the cockpit! Oh well, chalk this one up as part of learning process. :(

Rest of building process went surprisingly smoothly. Fuselage of the model fits together rather snugly, although care needs to be taken to align the parts together. Wing assembly was a bit more demanding, with upper parts of the wings not fitting with the lower part. The cause - surprise, surprise - the imprecise assembly of wheel wells. Well sides had to be filed down rather significantly before I achieved proper fit.

I don't feel I'm the right person to judge whether the fit between the fuselage and the wings is 'bad' or just 'demanding'. In any case, some additional work with filler and sanding sticks had to be done before I found the fit to my satisfaction.

Once past that last hurdle and having all main components in their intended places, I did have in my hands an lump of plastic that really did resemble a tiny Kittyhawk. It was time to bring out painting equipment.

Sword Models Curtis P40 Kittyhawk III - Part I

After six Airfix models in a row, I wanted to try a different manufacturer. As luck would have it, I remembered that one of my purchases during my initial shopping spree of last year was a Kittyhawk kit from a Sword Models, a company I never encountered before. Since I bought it during one of my trips, I had to ditch the box due to limited space, but here's the link to manufacturer's own homepage for this model.

Once I looked into the plastic bag, I remembered why I bought this kit in the first place. It was dirt cheap and the single plastic sprue gives the impression of the model being simple build. The detail is quite decent and you get two kits for the price of one. In other words, excellent value for the money!

For no particular reason, I made a bit of investigation about Sword Models and this kit in particular. The company is from Czech Republic and they seem to be a small operator, but with rather impressive range of products, some of them quite unusual. The actual kit is of so called "limited run" variety, a term previously unknown to me, but which I assume means that only limited number  of each kit is produced and once they are sold, they are gone from the market.

Once I started putting the kit together, it quickly became obvious that it is a peculiar blend of some parts having surprisingly high detail (or at least higher than what I was used to from Airfix) and basic, almost crude renditions of other parts of the airplane. During first stages of building the model, I was impressed by the detail of cockpit area, especially the instrument panel. Wheel wells on the other hand, while nicely detailed, are a true pain in the butt to work with. They consist of four pieces of plastic that need to be fitted together rather precisely for good result, but the model lacks any guides or supports that could be of any help in the fitting process. Instruction manual isn't of much help neither. In the end, I had to more or less guess what the right position was for individual walls of the wheel wells, with less than optimal results.

As it turns out, it was my first encounter with what in my opinion is a main problem with this kit - almost complete lack of guides and positioning pins makes this model a bit more challenging than your 'run of the mill' Airfix kit. Apparently, that's one of the common characteristics of those so called "limited run" kits - definitely something to keep in mind when thinking about getting one of those birds.

You get two of these sprues for the price of one.
Decent deal, if you ask me!

Cockpit sides have a bit of detail straight out of the box,

but the wheel wells are a pain to put together.

Instrument panel - I allowed myself a bit of artistic license
when painting it, so don't send any angry messages on the account
of altimeter being in wrong position.

My first clumsy attempt at detailing - head support made of "green stuff"
and seat belts cut out of thin metal foil, which in its previous life functioned as seal for
a jar of dry food for my fishes.